Pasi's Grow Log 2026

UmbriaFarmer

Well-Known Member
Joined
Feb 18, 2026
Messages
178
Points
63
Location
Umbria Italy
Thank you, thank you! I have this habit that whenever I make tools for myself, I like to put a little extra effort into making them look nice too. Somehow, they're just more enjoyable to use when they look good. And yes, it's metric. I'm from Finland. :)
Shamefully, I'm the opposite. If I make a tool or something for somebody else, I try to make it beautiful and perfect. If it's for my own use I just cobble it together out of any old rubbish, so long as it functions. I'm sure a psychiatrist would have a field day with that info...haha!
 

Pasiasiainen

Well-Known Member
Joined
Jun 28, 2025
Messages
126
Points
93
Location
Finland
Almost all the leaves are now in the kiln. I originally had the vacuum bags closed simply by rolling the open ends and securing them with clothespins. I left plenty of extra length to the bags (about 25 cm) so I could roll them up tightly. I've been checking about once a week how well the bags are holding moisture, and quite a few times the leaves have dried down to very low case.

Because of this, I decided to heat-seal all the bags, leaving a little air inside each one. Hopefully there's enough air/oxygen/whatever in there for the aging process to continue. I will open the bags after a week to check how things are going inside.

The smells coming out of those bags when I open them are amazing. Now that I have grown more varieties, it's really interesting to notice how different their aromas are.

011126Kiln.jpg

I was a bit surprised when I last checked the leaves I found a small patch of mold on one of the leaves. I removed that leaf and raised the kiln temperature by one degree to make sure it doesn't drop below 50°C, even for a short time. It's possible that the temperature isn't completely even throughout the kiln, despite the fans circulating the air, and that some spots have been a little cooler than others. The leaves are also in pretty high case.

011126Curing.jpg

Only CT Shade and Dominican Olor ligero are still in color curing, but they should be ready in a few days.

After color curing, I've been drying the leaves to make sure the midribs are completely dry. Then I bring them back to high case so I can flatten them a bit and pack them into vacuum bags. My Corojo 99 leaves grew so thick that getting them into high case takes three days in a plastic container with lots of moisture. The leaves are like veneer.

011126Corojo99.jpg

I got a call from the local energy company saying they need to replace a meter in my boiler room (which is currently pretty much filled with my curing tent). I'm desperately trying to schedule the visit far enough into the future that I'll have finished all color curing and drying, and taken down the tent before the technician arrives. That would save me from having a conversation with some suspicious-sounding explanation of what exactly I'm curing inside a plastic tent in my boiler room.
 

Pasiasiainen

Well-Known Member
Joined
Jun 28, 2025
Messages
126
Points
93
Location
Finland
A little kiln check-up.

The first batches of leaves have now been in the kiln about four weeks. I checked whether the vacuum bags and ziploc bags had kept the moisture inside, and only a few ziplocs needed a little extra moisture.

Dominican Olor, which had a strong green hue after color curing has turned out really well in the kiln. The leaves are now turning dark brown and all traces of green have disappeared.

CTSeco-2-061126.jpg Coro99Seco061126.jpg

DomOlorSeco061126.jpg PilotoCSeco061126.jpg

All the leaves are now in the kiln, and I've packed away the curing tent until next season. In the beginning of January the last batch will have spent eight weeks in the kiln.

So I guess it's time to go into hibernation mode now that the cold, rainy and dark Finnish autumn is at its worst. Hopefully we'll get some snow soon.
 

UmbriaFarmer

Well-Known Member
Joined
Feb 18, 2026
Messages
178
Points
63
Location
Umbria Italy
A little kiln check-up.

The first batches of leaves have now been in the kiln about four weeks. I checked whether the vacuum bags and ziploc bags had kept the moisture inside, and only a few ziplocs needed a little extra moisture.

Dominican Olor, which had a strong green hue after color curing has turned out really well in the kiln. The leaves are now turning dark brown and all traces of green have disappeared.

View attachment 61369 View attachment 61370

View attachment 61371 View attachment 61372

All the leaves are now in the kiln, and I've packed away the curing tent until next season. In the beginning of January the last batch will have spent eight weeks in the kiln.

So I guess it's time to go into hibernation mode now that the cold, rainy and dark Finnish autumn is at its worst. Hopefully we'll get some snow soon.
May the tobacco gods be with you!
 

Pasiasiainen

Well-Known Member
Joined
Jun 28, 2025
Messages
126
Points
93
Location
Finland
Okay, it is time to wrap up the 2026 growing season.

My goals for this season were:​

  • Start seedlings that are sturdier than last time
  • Learn how to grow different cigar varieties
  • Try shade growing
  • Figure out how to kiln different types of cigar leaves
  • Learn how to grow oriental tobacco and how to sun-cure it
  • Roll a decent cigar
So, how did it all go?

Start seedlings that are sturdier than last time​

I bought some grow lights and built a stand for them, and the result was strong, healthy seedlings. Every single one I transplanted grew really well. The difference compared to last season, when I grew my seedlings using only natural light, was huge.

I also got the timing of sowing right this year: 8 weeks before transplanting instead of 16 weeks like last year...

Learn how to grow different cigar varieties​

I'd say this was a success too, even though I messed up with overfertilizing and the leaves didn't want to show signs of maturity.

Curing seems to have gone well despite that, although at this point I still have no idea whether the leaves will turn out to be good quality or absolutely terrible. I did try smoking a leaf of Piloto Cubano in my pipe a few days ago, after four weeks in the kiln, and it tasted pretty promising!

Early in the season, it looked like the plants were barely growing and would end up tiny, but eventually they all reached a pretty good size.

I also learned some new things along the way, including how to measure soil pH and how to adjust it using different methods.

Try shade growing​

I built my shade structure from rose arches and aluminum tubes. It was quite a bit of work, and eventually I discovered that the structure was simply too small for four CT Shades.

I was also surprised by just how huge CT Shade can grow here in Finland. If it had had enough room, I'm pretty sure it would have grown well over 3 meters tall.

Unfortunately, because the structure was too cramped and the shade netting was quite coarse, some of the leaves got damaged from rubbing against it. Still, I ended up with a decent number of undamaged leaves, more than enough for my own needs.

Figure out how to kiln different types of cigar leaves​

Well, this turned out to be simpler than I expected. Based on the advice I got here on the forum, I just put all the leaves in the kiln for 8-10 weeks. Still waiting to see how that turns out.

Learn how to grow oriental tobacco and how to sun-cure it​

This one didn't go quite according to plan.

Samsun Maden grew reasonably well, but based on suggestions here on the forum, I eventually decided to flue-cure it instead. Sun curing probably wouldn't have worked very well here in Finland anyway.

Unfortunately, the flue-curing was pretty much a complete failure. I still don't know exactly what went wrong, but all the leaves ended up turning brown, and I didn't manage to get a single batch of nice yellow leaves.

Oh well, sometimes things just don't work out.

Roll a decent cigar​

I haven't really had a chance to practice this yet, but I've been keeping myself busy building a cigar cutter, and I'm planning to make some wooden cigar molds too.

I've already made a few prototypes, but making an accurate mold out of wood is surprisingly difficult. I might end up 3D printing a couple of molds after all, even though I'd much rather make them out of wood.

----

For some reason, this season felt like a lot of work.

We'll see what I decide to grow next season, or whether I'll take a year off. On the other hand, it would be nice to keep building up my tobacco stock, even if I only grow a small crop each year.

For now, though, it's time to enjoy the winter: ice fishing and smoking my pipe by a campfire. Then, towards the end of winter, I'll finally get serious about learning to roll cigars.

And a BIG, BIG thank you to everyone who helped me and gave me advice throughout the season, and to everyone else who kept a grow log here on the forum. It was really nice following everyone's progress during the season and learning new things along the way!

Special thanks to @deluxestogie , @StoneCarver and @The Haroo ln . You guys helped me out on so many occasions!

// Pasi
 

StoneCarver

Bureau for Paranormal Research and Defense
Joined
Aug 26, 2025
Messages
388
Points
93
Location
Winston-Salem,NC
For some reason, this season felt like a lot of work.
I felt the same way with my growing of tobacco this year. It ate up much more of my time than I expected. Tbf though, I couldn't keep my head out of my tobacco patch. For now all I'm doing is kilning; one more month and my second batch will be done. I'm trying to get caught up on life in the meanwhile; mostly I've been sewing and trying to repair some of my clothes that have gotten worn out. Once that's out of the way which should be in the next week or two, I'll start rolling cigars. I'm not in a rush as I don't really care for smoking cigars in cold weather.
Glad I could help. Here's to next year!
 

Pasiasiainen

Well-Known Member
Joined
Jun 28, 2025
Messages
126
Points
93
Location
Finland
It ate up much more of my time than I expected.
Same here. During the growing season, I didn't really mind spending so much time thinking about my tobacco plant and building all kinds of things. It was summer, and I was enjoying the whole process.

But once harvest time came around, things started to feel a bit exhausting. Sorting the leaves, the hassle of maintaining the right curing conditions for months, and juggling leaves at different stages of curing. I somehow managed to make even my leaf-hanging setup more complicated than it needed to be, and fiddling with all those wires was pretty frustrating from time to time.

And my vacuum bag kilning isn't exactly a set-it-and-forget-it setup either. I still spend a couple of hours every week checking and handling the leaves.

So there's still plenty of room for improvement to make the whole process as smooth as possible. And I guess as I gain more confidence in what I'm doing, things will become a bit more relaxed too, without having to worry too much about whether I'm doing things right or wrong.

Once early January comes around and all the leaves are finally out of the kiln, I think I'll be ready for a little break from all things tobacco. :)
 
Top